Inkheads - Revision history

TJ at 16:37, 1 November 2017

2017-11-01T16:37:07Z

TJ at 16:36, 1 November 2017

2017-11-01T16:36:36Z

TJ: Created page with "= Inserting Inkheads =

Remove the orange protective caps by pulling them down.
Figure 1: Removing the protective caps from the printhead File:RemoveProt..."

2017-11-01T16:14:18Z

Created page with "= Inserting Inkheads = <ul><ol> <li>Remove the orange protective caps by pulling them down.</li> Figure 1: Removing the protective caps from the printhead File:RemoveProt..."

New page

= Inserting Inkheads =

<ul><ol>
<li>Remove the orange protective caps by pulling them down.</li>

Figure 1: Removing the protective caps from the printhead

[[File:RemoveProtectiveCaps.png]]

<li>The printhead is designed to prevent you from accidentally inserting it into the wrong slot. Check that the colored label on the printhead matches the colored label of the carriage slot into which the printhead is to be inserted.</li>
<li>Insert the new printhead into its correct slot in the carriage.</li>

CAUTION: Insert the printhead slowly and vertically, straight down. It can be damaged if you insert it too quickly, or at an angle, or if you rotate it as you insert it.
Figure 2: Inserting the printhead

[[File:InsertPrinthead.png]]

<li>Push down as indicated by the arrow.</li>

Figure 3: Pushing in the printhead

[[File:PushInPrinthead.png]]

CAUTION: You might feel some resistance when installing the new printhead, so you need to press it down firmly but smoothly. You should hear a beep and see confirmation on the front-panel display that the printhead has been inserted
<li>Insert all of the other printheads that need to be installed, and close the carriage cover.</li>

Figure 4: Closing the carriage cover

[[File:CloseCarriageCover.png]]

<li>Make sure that the end of the blue handle catches the wire loop on the near side of the carriage.</li>

Figure 5: Closing the carriage cover, step 2

[[File:CloseCarriageCover2.png]]

<li>Lower the handle to rest on the carriage cover.</li>

Figure 6: Closing the cover, step 3

[[File:CloseCarriageCover3.png]]

When all of the printheads have been inserted correctly and the printer has accepted them, the printer beeps.
NOTE: If the printer does not beep when you insert the printhead and the Replace message appears on the front-panel display, you might need to reinsert the printhead.
<li>Close the printer window.</li>

Figure 7: Closing the printer window

[[File:ClosePrinterWindow.png]]

<li>The front-panel display confirms that all of the printheads are correctly inserted. The printer starts checking and preparing the printheads. The default routine process, when all printheads are changed, takes about 18 minutes. If the printer identifies a problem when preparing the printheads, the process takes longer, up to 30 minutes. For a single printhead insertion, the time varies between 10 and 20 minutes. After all printheads are checked and prepared, the printhead realignment procedure runs automatically if paper is loaded.</li>
</ol></ul>

@@ Line 1: / Line 1: @@
-= Removing Inkheads =
+= Removing Printheads =
 Printhead replacement must be performed after the printer has been turned on with the hard power
@@ Line 42: / Line 42: @@
 </ol></ul>
-= Inserting Inkheads =
+= Inserting Printheads =
 <ul><ol>

← Older revision		Revision as of 16:36, 1 November 2017
Line 1:		Line 1:
		+	= Removing Inkheads =
		+
		+	Printhead replacement must be performed after the printer has been turned on with the hard power
		+	switch at the back of the printer.
		+
		+	<ul><ol>
		+	<li>At the front panel, select the [[File:Ink.png]] icon, then select Replace printheads.
		+
		+	<li>The printer moves the carriage into the correct position.</li>
		+
		+	CAUTION: If the carriage remains in the removal position for more than 3 minutes without inserting or removing any printheads, it will attempt to return back to its home position to the right.
		+	<li>When the carriage has stopped moving, the front panel prompts you to open the printer window.</li>
		+
		+	[[File:OpenPrinterWindow.png]]
		+
		+	<li>Locate the carriage on the right side of the printer.</li>
		+
		+	[[File:LocateCarriage.png]]
		+
		+	<li>Pull up and release the latch on top of the carriage.</li>
		+
		+	[[File:PullUpLatch.png]]
		+
		+	<li>Lift up the cover. This provides access to the printheads.</li>
		+
		+	[[File:LiftCover.png]]
		+
		+	<li>To remove a printhead, lift up the blue handle.</li>
		+
		+	[[File:LiftBlueHandle.png]]
		+
		+	<li>Using the blue handle, gently disengage the printhead.</li>
		+
		+	[[File:DisengagePrinthead.png]]
		+
		+	<li>Gently pull the blue handle upward until the printhead is released from the carriage.</li>
		+
		+	[[File:PullBlueHandle.png]]
		+
		+	CAUTION: Do not pull abruptly. That action can damage the printhead.
		+	<li>The front-panel display identifies the missing printhead.</li>
		+	</ol></ul>
		+
	= Inserting Inkheads =		= Inserting Inkheads =

Inkheads - Revision history

TJ at 16:37, 1 November 2017

TJ at 16:36, 1 November 2017

TJ: Created page with "= Inserting Inkheads = Remove the orange protective caps by pulling them down. Figure 1: Removing the protective caps from the printhead File:RemoveProt..."

TJ: Created page with "= Inserting Inkheads =

Remove the orange protective caps by pulling them down.
Figure 1: Removing the protective caps from the printhead File:RemoveProt..."