Difference between revisions of "LaserJet Paper"
From College of Art and Design IT Wiki
(Created page with "= Loading Paper = # Open the tray. File:OpenTray.png # Adjust the paper-length and paper-width guides by squeezing the adjustment latches and sliding the guides to the...") |
|||
| Line 1: | Line 1: | ||
| − | = Loading Paper = | + | = Loading Paper (Not Tray 1) = |
| − | + | <ul><ol> | |
| + | <li>Open the tray.</li> | ||
[[File:OpenTray.png]] | [[File:OpenTray.png]] | ||
| − | + | <li>Adjust the paper-length and paper-width guides by squeezing the adjustment latches and sliding the guides to the size of the paper being used.</li> | |
[[File:AdjustGuides.png]] | [[File:AdjustGuides.png]] | ||
| − | + | <li>Load paper into the tray. Check the paper to verify the guides lightly touch the stack, but do not bend it.</li> | |
[[File:LoadPaper.png]] | [[File:LoadPaper.png]] | ||
| − | + | <li>Close the tray.</li> | |
[[File:CloseTray.png]] | [[File:CloseTray.png]] | ||
| − | + | <li>The control panel prompts you to set the paper size and type. Select the Custom setting, and then configure the X and Y dimensions of the custom paper size.</li> | |
[[File:DetermineDimensions.png]] | [[File:DetermineDimensions.png]] | ||
NOTE: See the label in the paper tray, or the following illustration, to determine the X and Y dimensions. | NOTE: See the label in the paper tray, or the following illustration, to determine the X and Y dimensions. | ||
| + | </ol></ul> | ||
| + | |||
| + | = Loading Paper (Tray 1) = | ||
| + | |||
| + | <ul><ol> | ||
| + | <li>Open Tray 1.</li> | ||
| + | |||
| + | [[File:OpenTray1.png]] | ||
| + | |||
| + | <li>Pull out the tray extension to support the paper.</li> | ||
| + | |||
| + | [[File:PullOutTrayExt.png]] | ||
| + | |||
| + | <li>Load paper in the tray.</li> | ||
| + | |||
| + | [[File:LoadPaperTray.png]] | ||
| + | |||
| + | <li>Make sure the stack fits under the tabs on the guides and does not exceed the load-level indicators.</li> | ||
| + | |||
| + | [[File:StackFitsInGuides.png]] | ||
| + | |||
| + | <li>Adjust the side guides so that they lightly touch the paper stack but do not bend it.</li> | ||
| + | |||
| + | [[File:AdjustSlideGuides.png]] | ||
| + | </ol></ul> | ||
Latest revision as of 17:41, 1 November 2017
Loading Paper (Not Tray 1)
- Open the tray.
- Adjust the paper-length and paper-width guides by squeezing the adjustment latches and sliding the guides to the size of the paper being used.
- Load paper into the tray. Check the paper to verify the guides lightly touch the stack, but do not bend it.
- Close the tray.
- The control panel prompts you to set the paper size and type. Select the Custom setting, and then configure the X and Y dimensions of the custom paper size.
NOTE: See the label in the paper tray, or the following illustration, to determine the X and Y dimensions.
Loading Paper (Tray 1)
- Open Tray 1.
- Pull out the tray extension to support the paper.
- Load paper in the tray.
- Make sure the stack fits under the tabs on the guides and does not exceed the load-level indicators.
- Adjust the side guides so that they lightly touch the paper stack but do not bend it.
